Getting Started with Plumbing Basics for Bathtub Installation
Getting Started with Plumbing Basics for Bathtub Installation
Blog Article
The content in the next paragraphs about How to Install a Bathtub Yourself is pretty much informative. Check it out for yourself and figure out what you think of it.
Mounting a bathtub isn't precisely brain surgery, but it does require strong plumbing, woodworking, and also sometimes, tiling skills. Replacing an old tub with a new one is also a reasonably difficult job. If the old tub is easily easily accessible, the task can relocate easily; if you need to open a wall to remove the old tub and place the brand-new tub, the job is a lot harder. In either case, the project is within a residence handyman's skills, although you will certainly need an assistant to vacate the old bathtub and also set in the new one. Ensure you have qualified on your own for the work and also are comfortable attempting it. As opposed to hiring a specialist to take control of a halfway-completed task, it is much better to take into consideration utilizing one before you begin. Chances are you might require a specialist plumber to make tube connections.
This short article will assist you mount a brand-new bathtub in your bathroom if you have actually currently bought a new tub and don't need to change the arrangement of your previous water pipes.
Your tools as well as product list need to consist of the following:
Getting ready for the Installation
Firstly, the supporting structure supplied with the bath should be fitted (if needed) according to the supplier's guidelines. Next off, fit the taps or mixer to the bathtub. When suitable the tap block, it is essential to make certain that if the tap features a plastic washing machine, it is fitted between the bathroom and also the taps. On a plastic bathroom, it is likewise reasonable to fit a sustaining plate under the faucets unit to prevent stress on the tub.
Fit the flexible faucet ports to the bottom of the two taps using 2 nuts and also olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet via the hole in the bathroom. Use the nut supplied by the maker to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the versatile overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which should be fitted inside the bath. See to it you utilize all of the supplied washing machines.
Connect the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom ought to now be ready to be suited its last position.
Removing Old Taps
If you require to replace old taps with new ones as a part of your installation, then the first thing you must do is separate the water system. After doing so, switch on the faucets to drain any kind of water continuing to be in the system. The procedure of getting rid of the existing faucets can be quite troublesome because of the limited gain access to that is typically the instance.
Use a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipes to the taps. Have a cloth ready for the staying water that will certainly come from the pipelines. When the supply pipes have been removed, make use of the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will require to quit the solitary taps from transforming throughout this process. Once the taps have been eliminated, the holes in the bath/basin will certainly need to be cleansed of any old securing compound.
Prior to moving on to fit the new faucets, contrast the pipeline connections on the old taps to the new faucets. If the old taps are longer than the new faucets, after that a shank adapter is needed for the brand-new faucets to fit.
Installing the Tub
Utilizing both wooden boards under its feet, put the bath tub in the required setting. The wooden boards are handy in equally spreading out the weight of the bath tub over the location of the boards as opposed to focusing all the weight onto four tiny points.
The following goal is to make certain that the tub is leveled all round. This can be achieved by checking the spirit level as well as changing the feet on the bath tub till the spirit level reviews level.
To mount taps, fit all-time low of the furthest flexible tap port to the ideal supply pipe by making a compression join; after that do the very same for the other tap.
Activate the water and also inspect all joints and also brand-new pipework for leaks and tighten them if necessary. Load the tub and additionally inspect the overflow outlet and also the normal outlet for leakages.
Lastly, fix the bathroom paneling as described in the manufacturer's user's manual. Tiling and sealing around the bathtub should wait till the tub has actually been used a minimum of once as this will certainly resolve it into its final placement.
Suitable New Taps
If the tails of the new taps are plastic, after that you will certainly require a plastic adapter to avoid damages to the string. One end of the port fits on the plastic tail of the faucet and the various other end provides a connection to the current supply pipes.
If you require to fit a monobloc, after that you will certainly call for minimizing couplers, which connects the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next, place the faucet in the installing hole in the bath/basin making sure that the washing machines are in location between the tap and also the sink. Safeguard the tap in position with the supplier offered backnut. Once the faucet is securely in place, the supply pipes can be connected to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with regular faucet adapters. The former type needs to be linked to the tap finishes initially, tightening only by hand. The supply pipelines can later be connected to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Bathtub
In the area where the bathroom meets the floor tile, it is needed to secure the accompanies a silicone rubber caulking. This is necessary as the fitting can move enough to crack a stiff seal, causing the water to penetrate the wall between the bathroom and also the tiling, resulting in difficulties with moisture and possible leaks to the ceiling below.
You can pick from a range of coloured sealants to assimilate your fixtures as well as installations. They are offered in tubes and also cartridges, and also are capable of sealing spaces as much as a width of 3mm (1/8 inch). If you have a bigger void to load, you can load it with spins of soaked paper or soft rope. Bear in mind to always fill up the bath tub with water prior to sealing, to allow for the activity experienced when the bathtub remains in usage. The sealer can fracture fairly early if you do not take into account this movement before securing.
Alternatively, ceramic coving or quadrant tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are additionally conveniently available on the marketplace. It is a good idea to fit the tiles utilizing waterproof or waterproof sticky and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I came across that review about A Step-by-Step Guide to Installing a Bathtub when doing a lookup on the web. If you liked our article please make sure you remember to share it. Thanks a lot for taking the time to read it.
Request Estimate Report this page